Why Does Honey Crystallize?

Honey comb

It may seem intuitive to assume that crystallized honey is spoiled or poor quality, but this isn’t the case at all. Crystallization happens naturally over time to pure, raw honey and actually helps preserve the nutrients and quality. Additionally, you may find that crystallized honey is easier to spread and richer in flavor.

The Chemistry of Honey Crystals

The “why” behind the crystallization of honey is simple chemistry. Usually, honey contains at least 70% carbohydrates and less than 20% water. This is more sugar than can naturally remain dissolved and over time, crystals begin to form. Some honey crystals are fine and smooth while others are large and gritty. This is largely due to the proportion of the two main types of sugars found in honey, fructose and glucose. While fructose tends to remain dissolved, glucose has a much lower solubility. The higher proportion of glucose honey contains, the more quickly it will crystalize. More rapidly crystallized honey contains finer, smoother crystals. In fact, creamed honey is honey that has been crystallized so rapidly, that the minuscule crystals create a smooth, creamy texture.

Can you de-crystallize honey?

liquid honey

Yes! Honey can easily be de-crystallized in small batches through simple heating. Remember, however, that in order to preserve the natural nutrients found in honey, overly hot temperatures should be avoided.

 

You can easily de-crystallize honey on a stovetop using the following steps:

 

  1. Make sure your honey is in a glass jar or jars (not plastic). Fill a pot with water that comes to ½ to ⅔ up the sides of the jars.
  2. Place honey jars (sans lids) in pot and bring water to a hot but not boiling temperature.
  3. Gently stir honey every few minutes to help break up crystals. Be careful not to splash any hot water into honey jars.
  4. Remove jars from heat when honey is once again smooth and runny.
  5. Tightly seal jars and store in a cool, dry place.

 

How to Keep Honey From Crystallizing

de-crystalizing honey

Remember, crystallized honey happens naturally over time. Some steps, however, can be taken to minimize or delay crystallization.

  • Maintain steady heat (104°-140°F) during honey bottling.
  • Provide a quick, mild heat treatment (140°-160°F) to dissolve any crystals and expel air bubbles that could initiate crystallization.
  • Store honey in proper containers. Air-tight, water safe stainless steel drums are recommended.
  • Store honey in a cool (50°-70°F), dry location. Storage temperatures above 70°F will compromise the quality and nutrients of the honey over time. Refrigerated storage will quickly crystallize honey and should be avoided.

 

Honey Heating Blankets

Powerblanket Bee Blanket

An effective solution to minimizing crystallization during the honey manufacturing process is utilizing a heating blanket.  The Powerblanket Bee Blanket is ideal because it keeps honey at hive temperatures and prevents loss of nutrients or burning from overheating. If you’re in the business of honey, consider adding a Bee Blanket or other method of temperature control to your manufacturing process. While crystallization can’t necessarily be avoided, a Bee Blanket can help keep your honey at the ideal, smooth viscosity.

Grave Digging and Ground Thawing

We’re gradually approaching warmer weather now, but it’ll still be some time before the ground thaws and makes digging a lot less difficult. That’s why we’d like to introduce you to our Ground Thawing Blankets. For those in concrete, grave digging, utility maintenance, or any other digging / ground-prep-related project, Powerblanket® Ground Thawing Blankets can be a really big help.

 

image-ground-thawing-blanketsFrom Grave Digging to Concrete Prep

Whether you’re laying concrete or preparing a funeral plot, our ground thawing blankets can make the process a whole lot easier. Powerblanket Ground Thawing blankets help to thaw frozen ground prior to digging. And in the case of preparing ground for a funeral in the winter or early spring, ground-thawing assistance can make the process run a lot smoother. Here are some words from a satisfied customer who used our ground thawing blankets for their business:

“Your blankets are absolutely excellent. Thanks to Powerblanket, we were able to quickly thaw the ground and complete our job. In fact, we estimate a savings of 10 hours per site, equaling a savings of $5,000 already. Calculating this into our thousands of sites, the savings are huge! We are excited about the time and money Powerblanket has saved us and look forward to future savings.”

Our patented blend of technology and our use of durable materials enable us to deliver high watt density throughout the entire area of application, making ground thawing through electrical heat transfer safe and highly efficient. So when it comes to preparing a plot for burial, use our ground thawing blankets to make the task much easier.

 

Why Powerblanket® Ground Thawing Blankets?

  • High watt density thaws frozen ground fast
  • Quickly remove frost prior to digging
  • Melt snow and ice from ground prior to digging
  • Easily installed and removed
  • Easily transportable
  • Safe and certified to national safety standards

 

Some Things to Remember

Remember that thawing ground goes a lot faster if you first manually remove as much snow and ice as you can.  If you have a foot of snow, remove it all, then apply the blankets.  A foot of snow can add a day to the process if not removed first.

Secondly, thawing frozen ground through a layer of grass can be problematic.  The grass tends to hold the blanket up and away from the frozen ground, making the thawing process much longer than it would be with bare ground.  If a Powerblanket ground thawing blanket is left in place too long, it WILL kill the turf. So if keeping the turf healthy and intact is the goal, then don’t use a ground thawing blanket. However, if you’re trying to thaw the ground for digging purposes, then remove the grass first.

 

button (16)

Custom Tank Heaters: The Perfect Approach to Heating Solutions


custom tank heatersIt would be absolutely ridiculous to assume that all tanks come in the same shapes and sizes, whether they hold water, gas, chemicals, or some other matter. We all know that this simply isn’t the case. While there are certainly standard measurements for specialty gas tanks, water tanks, and others, the range of variance between size, construction, and purpose is vast enough that there simply isn’t a one-size-fits-all solution for tank protection. That’s why Powerblanket® Custom Tank Heaters are the perfect approach to the need for a heating solution.

 

Customized for Your Tanks and Needs

Regardless of the size of your tank, the purpose it serves, or its shape, Powerblanket can help you protect it against cold weather and keep it running at the ideal temperature year round. Our custom approach to providing tailored heating solutions to a myriad of industries and applications has allowed hundreds of customers to protect their precious assets from the ravages of cold weather.

In addition to freeze protection, our custom tank heaters enable increased efficiency in gas and other kinds of tanks. Anywhere flow rates and extraction rates are affected by temperature, Powerblanket custom tank heaters can ensure the flow of liquids and extraction of gas is always at its best. Take, for example, the nature of a gas such as propane.

When gases are stored in tanks, they are stored under considerable pressure. Due to this fact, they reside in the tank in both a liquid and gaseous state. Extracting a gas means you must evaporate some of the liquid and that evaporation process requires an input of heat energy. If the gas extraction rate is fast enough, it could cause the tank to frost up and the extraction to be impeded. However, with a custom Powerblanket propane tank heater you can keep the extraction flowing fast and full, without the side effect of frosting or icing.

What’s more, whether a tank holds gas or liquid, freezing temperatures pose big problems. Using a custom tank heater allows you to fully insulate and heat your tank to whatever temperature is best, regardless of the surrounding climate.

 

custom tank heaterGetting a custom tank heater from Powerblanket is as easy as 1, 2, 3:

  1. Contact us with the details of your application.
  2. We’ll design a custom tank heater for your application, based on your information and feedback.
  3. We’ll build your custom solution and ship it to you within two weeks. (Sometimes, we can even turn a project around in as little as one week.)

 

In the end, there’s no reason to leave your tank out in the cold. Powerblanket can cover it and keep it safe and functioning well through the most inclement weather.

 

Get a custom quote

Custom Heating Solutions Don’t Take as Long as You Think

Custom Heating BlanketsOften times when we think of customization, or taking a custom approach to something, the first thing that comes to mind is time. “How long is that going to take?” we ask ourselves. Well, in the case of Powerblanket custom heating solutions, not too long at all. Our custom approach to heating solutions doesn’t take as long as you might think. In fact, in most cases, Powerblanket can turn around a custom project in one to two weeks.

 

Custom is the Way to Go

Many applications can be adequately covered by our ready-to-ship product line, but there are equally as many projects that need a custom solution. Powerblanket works with many companies in a myriad of industries to supply custom heating solutions to a wide range of needs. So what does a custom heating solution process look like when working with us? We’ll show you.

Powerblanket’s custom heating solutions can be tailored to fit just about any application. If you can build it, produce it, or store it, Powerblanket can cover it. What’s more, completing a custom project with us can be summarized in three easy steps:

 

  1. Contact us and tell us the details of your application. (Many of our custom projects start with a simple phone call to one of our reps. From here, you can send any and all information we’ll need to form the proper heating solution for you. Additionally, we do offer what we refer to as the white glove treatment. In other words, we can come onsite and get all the details on our own.)
  2. We’ll design a custom heating solution for your application, based on the information and feedback we gather or you deliver to us. (Whether you choose to send us information or want us to come onsite, we will get all the details we need.)
  3. We’ll build your custom solution and ship it to you within two weeks. (Sometimes, we can even turn a project around in as little as one week.)

 

Case In Point

When Enduraplas’s plastics manufacturing process needed heating assistance, Powerblanket was able to deliver a custom tank heater that increased efficiency beyond expectations. Enduraplas’s manufacturing process uses propane extensively—making their large propane tanks an invaluable asset. However, cold weather threw a real damper on the whole thing, impeding the flow of propane significantly.
With the Poweblanket custom heating solution in place, however, Enduraplas was able to run their manufacturing processes through the coldest of weather.

 

READ MORE

 

Gold Coast Yachts is another great example of how Powerblanket custom heating saved immense amounts of time and money. Gold Coast Yachts builds custom, carbon-fiber yachts, and the curing process for the large sections of carbon-fiber frames needs high-temperature exposure for long periods of time. Previous to implementing the Powerblanket custom curing blankets, Gold Coast had to architect, build, and utilize large custom ovens for every cure. In other words, they had to build a large shed around every frame in order to pipe heat into the enclosure and cure the resins at the proper temperature. This process, as you can imagine, took a whole lot of time, manpower, and money. With Powerblanket, however, Gold Coast Yachts was able to save thousands of dollars and hours of time on each project.

 

READ MORE

 

When Cenovus turned to Powerblanket to design a custom valve and transmitter heating solution, Powerblanket was able to turn the product around with ease and speed. Powerblanket set out to create a custom heating system that eliminated the risk Cenovus had of losing money to freezing valves and transmitters. After Powerblanket completed the project, Cenovous no longer had to worry about the cost associated with downtime and the thawing of frozen instrumentation and valves.

 

READ MORE

 

Get a custom quote

Heating and Hazardous Locations

Working in hazardous locations means you have to exercise serious caution regarding procedure, protocol, and equipment usage. What’s more, heating in hazardous locations takes all the more care and detail to make certain you aren’t adding fuel to a potential fire. This is why Powerblanket offers products certified to national safety standards.

 

CID2Class I Division 1 and Class I Division 2

We understand that hazardous location heating is nothing to take lightly. And we understand that heating products should be engineered to the highest standards of quality and safety. We’ve based our business on this simple reality and are able to customize our safe and innovative heating solutions to a myriad of industries because of it. In fact, our custom heating solutions can be designed and certified to Class I Division 1 (CID1) or Class I Division 2 (CID2) safety standards. We are certified for all four gas Groups, A, B, C, and D and up to a T4 Temperature Classification.  Many people who work in hazardous locations are familiar with these terms. For everyone else, here’s an explanation.

The classifications referenced as CID1 and CID2 regard the operation of electronic equipment in hazardous locations. CID1 is the identifier used for locations where ignitable concentrations of flammable gases, mists or vapors could possibly exist under normal working conditions. This classification also covers locations where the same gases, mists or vapors may exist frequently due to repairs or maintenance in the area. It also includes potential scenarios where gases, mists or vapors could be leaked by faulty or damaged equipment.

CID2, on the other hand, represents all locations where concentrations of flammable gases and/or vapors and/or mists are present in the air under operating conditions outside of the norm. So CID1 covers areas where such hazards are normally present, and CID2 covers areas where such hazards aren’t normally present but certainly could be under abnormal circumstances. Most importantly, if a product is CID1 or CID2 certified, it means that product is safe to use in locations that are CID1 or CID2 rated hazardous locations.

Powerblanket provides products that are certified to either of these hazardous location equipment safety standards. So when it comes to heating in hazardous areas, Powerblanket is both an efficient and safe choice. In addition to these ratings, Powerblanket products are also certified to UL, and CSA standards. Our innovative approach to providing industry-specific heating solutions has helped our customers save a lot of time and resources to safeguard and increase efficiency among the assets that keep their businesses running. So whether it’s freeze protection, viscosity maintenance, curing assistance, or some other heat-related dilemma, Powerblanket can help, even if you operate in a hazardous location.

 

Learn More

Propane Tanks and How to Care for Them

Whether you’re a homeowner who relies on propane for heating, or a business leader who uses if for industrial purposes, propane is a versatile and important commodity. However, as helpful as propane is to us, we often overlook the need of caring for our propane tanks year round.

 

2016-01-05 09_16_31-Powerblanket___Propane_Tanks_Guide___v3__1_ (1).pdf - Adobe ReaderCaring for Your Propane: Tank and All

When it comes to caring for your propane storage, it’s imperative that you have a working knowledge of your tank and all the potential threats that could impede its proper functionality. Understanding the warning signs of a damaged or inefficient tank is important, not only for reasons of economical operation, but for the safety of all involved.

Several factors play into the safe and efficient operation of any size propane tank. These factors include, but aren’t limited to:

  • Shutting off valves when the tank is not in use
  • Keeping reserve tanks at a minimum
  • Not leaving portable propane tanks inside a vehicle
  • Securing portable tanks properly
  • Replacing weathered and/or worn canisters

Knowing how to properly manage all these aspects of propane storage and usage is very important. But there are many other factors to consider, too. Matters such as storage, setup, protection, government regulations, and the warning signs of hazardous circumstances are equally important. For more information on how to care for your propane and the tank in which you keep it. Access our free e-book below.

 

button (11)

 

DEF Tank Heaters: Storage and Beyond

If you run any sort of diesel engine, then you know how important DEF is these days. You can’t do business without it. However, wintertime poses a real problem to storing DEF. Then again, storage is only half of the problem. What do you do with your DEF in transit? Or worse yet, what do you do when your engine isn’t running. Thankfully, we have the answer with our DEF tank heaters.

 

DEF Tank HeaterDEF Tank Heaters

Protecting your DEF in storage is very important, but like we said already, it’s only half the problem. Protecting your DEF from freezing temperatures once it’s in the truck tank becomes equally important. The transportation and commercial trucking industries know just how frustrating it is when DEF freezes in the truck tank.

This problem has been around since the inception of Diesel Exhaust Fluid (DEF). But innovative truck manufacturers solved the problem by running their coolant system through the DEF tank. And it worked too, as long as the truck was running. That’s the catch, you see. This type of DEF heating solution only works when the engine is running. After parking a truck overnight in cold weather, the DEF could freeze up entirely. What’s more, it could take as much as 30 minutes to several hours of idling to thaw out a DEF popsicle. Running the truck with frozen DEF will likely trip the sensors too, indicating a false reading within truck computer and adversely affecting its performance.

Instead of taking a chance with winter, and losing valuable time as a result, trucking companies can turn to Powerblanket for an innovative solution to this dilemma. Powerblanket has developed an insulated heating blanket designed to fit the DEF tanks installed in commercial trucks. These DEF tank heaters offer both insulation and regulated heat that will keep your DEF at the ideal temperature. The Powerblanket DEF tank heater is certified to national and international safety standards and is easy to install, remove, and reinstall.

With options for either AC or DC voltage and the choice of a ten or fifteen-foot cord, our DEF tank heaters are easy to apply on your truck and plug in to keep your DEF warm when the engine isn’t running. So put the worry of frozen DEF aside this winter, and reach out to us for your DEF tank heaters today.

 

CTA-button

Insulated Band Heaters vs. Traditional Band Heaters

If you’ve dealt with traditional band heaters, then perhaps you have some reservations regarding the usefulness, efficiency, and safety of such a solution. If you’ve never heard of insulated band heaters, then you’re in for a treat. Here we compare the two to see who comes out on top.

 

Insulated band heatersInsulated Band Heaters vs Traditional Band Heaters

In one corner we have the long-standing, often-used traditional band heater, and in the other corner, we have the heavy-hitting, highly efficient insulated band heater. Let’s start with comparing maximum temperatures. Traditional band heaters can heat as high as 400° F, insulated band heaters, well, they can too. Here’s what that looks like:

 

Traditional Band Heater Insulated Band Heater
Heats as high as 400° F Heats as high as 400° F

 

Traditional Band Heaters: 1 pt.

Insulated Band Heaters: 1 pt.

 

Next, we look at heating efficiency. Traditional band heaters use anywhere from 600-1200 watts of electricity to heat the material inside a barrel or drum. What’s more, a good portion of this is wasted as heat is lost to the air around the heater. Insulated band heaters, on the other hand, don’t lose as much energy to their surroundings. With insulated band heaters, much more heat is channeled into the product, and much less into the thin air.

 

Traditional Band Heater Insulated Band Heater
Wastes a lot of energy Delivers energy to the load

 

Traditional Band Heaters: -1 pt.

Insulated Band Heaters: 2 pt.

 

And finally, when it comes to that most important topic of safety, insulated band heaters win out here too. Traditional band heaters can be extremely hazardous. Since they’re heating as high as 400° F, this means their non-insulated, external temperature is about the same. Essentially, you have a belted band of silicone wrapped around your drum or barrel that is as hot as 400° on the surface. If something touches this on accident, it could mean fire or third-degree burns. Insulated band heaters are a lot safer. Since they’re insulated, the surface that is exposed to the user  is safe to touch.

 

Traditional Band Heater Insulated Band Heater
Hazardous (fire hazard and burn hazard) Safe to touch when installed and running

 

 

Traditional Band Heaters: -1 pt.

Insulated Band Heaters: 2 pt.

 

So this puts the final score of the comparison at…

 

Traditional Band Heater Insulated Band Heater
Heats as high as 400° F (1 pt.) Heats as high as 400° F (1 pt.)
Wastes a lot of energy (-1 pt.) Delivers energy to the load (2 pts.)
Hazardous (fire hazard and burn hazard) (-1 pt.) Safe to touch when installed and running. (2 pts.)

 

Traditional Band Heaters: -1 pt.

Insulated Band Heaters: 5 pts.

We’ll let you do the math from here.

 

 

Picture1

Powerblanket Receives Manufacturer of the Year Award from UMA

If you haven’t seen this headline somewhere else on the web by now, we’re happy to tell you all about it here. Utah Manufacturers Association recently awarded Powerblanket something we’re pretty happy about. Read on to learn more about the UMA Manufacturer of the Year Award.

 

UMA AwardUMA and Manufacturer of the Year

Utah Manufacturers Association (UMA), recently awarded Powerblanket the prestigious award  of Manufacturer of the Year. This award is given annually to the Utah-based manufacturer that proves to be the most innovative contributor to their space. There’s even more to it than this, but we’ll get to that.

UMA has been around since 1905. The organization prides itself on offering the “voice of industry” in the state of Utah, and they’ve been doing so for over 107 years now. UMA has clearly been talking Utah economy for a long time, but talking isn’t all they do. UMA is a trade association, and their goal is to enhance and improve the business climate in the state. UMA doesn’t only offer insight and expertise in the business of manufacturing, but the organization also has considerable experience in the legislative processes of state government. This is how they can do so much to vie for the interests of Utah businesses and the overall economic prosperity of the state.

UMA’s Manufacturer of the Year Award embodies the mission of UMA in multiple ways. By awarding the company that not only proves innovative in their respective markets, but also offers leadership in their industry, UMA’s award encourages and rewards the same idealism by which their organization operates. Powerblanket was chosen to receive this award for 2015, based on the embodiment of these characteristics and more. In fact, why don’t we just give it to you in their own words. According to UMA, Powerblanket received the award “for their outstanding performance in operational excellence, economic achievement, workplace safety, community outreach, and fidelity to the principles of free enterprise.”

Powerblanket is honored to receive such accolades from a high quality establishment like UMA. The credibility of UMA and the Manufacturer of the Year Award lends a great addition to our own image and ethos as a company devoted to “operational excellence, economic achievement, workplace safety, community outreach, and fidelity to the principles of free enterprise.”

So, from all of us here at Powerblanket, thank you, UMA for this great privilege.

 


Learn More

Protect Your Agricultural Assets With Custom Heating Solutions

Forbes ran an article yesterday from Thomas Landstreet about the potential collapse in agricultural pricing. These estimations come at the cost of corn, pork, and beef especially. But whichever way the pendulum swings in the near future, one thing’s for certain: those in agriculture will need to safeguard their precious assets, and this could mean applying the proper custom heating solutions to help keep operating costs low.

 

The Agricultural Outlook

Protect Your Agricultural Assets With Custom Heating Solutions

According to Thomas Landstreet’s article on the matter, we should expect to experience a considerable drop in prices for the agricultural sector (that’s bad news) something Mr. Landstreet refers to as a retrenchment. So why the retrenchment, you ask? Well, according to Landstreet, there are two major factors that will contribute to the impending slide of the agricultural industry. One of them is something its faced time and time again, and that’s drought. Apparently the drought we passed through back in 2012 has created what Landstreet calls a bubble, one that he thinks will pop soon.

The second factor that is set to cause problems in the agricultural space is the ethanol mandate that allocated 40% of corn to creating an alternative fuel to petroleum. The effect of less corn going toward food supply has also contributed to the nearly bursting bubble. Whether the bubble bursts anytime soon or not, one thing is pertinent for the industry, and that is asset protection.

 

The Powerblanket® Contribution

If prices are to drop in the agricultural sector, then those involved in the industry are going to need to save on operating expenses where ever they can. Additionally, it’s going to be imperative to safeguard capital and resources. In the spirit of such, Powerblanket offers a myriad of possibilites in custom heating solutions for the agricultural space. So whether you need to keep large water tanks from freezing, propane storage at the ideal temperature, or DEF storage working in cold weather, Powerblanket has you covered.

Powerblanket custom heating solutions offer the most cost-effective and efficient heating solution on the market. With our patented approach to heating, we can ensure even heat distribution over the entire service area of application. What’s more, in case of temperature-sensitive storage maintenance, Powerblanket heating solutions actually add efficiency to the equation, such as in the case of ourpropane tank heaters. Add to this our revolutionary smart controllers and our new 3D scanningcapabilities, and Powerblanket becomes the clear choice.

 

Download Propane Spec Sheet